tools & hardware: E. Emerson Tool Co ... (t-track 54-inch 8-inchx)

tools & hardware: E. Emerson Tool Co ...

tools & hardware:

All in One Clamp U99 99" Ultra All In One Clamp

12 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Great product
I am a general contractor and do many of the smaller jobs as well. I have owned a competitor's 48" brand for years and love using it on the bottom of doors for a straight cut. I had been looking for an 8'version so I could use it to rip down the width of doors plus plywood accurately. When I ran across this, I was excited and purchased it immediately. I have used it on several applications and I ...

All in One Clamp A-36 36-Inch Grip Clamp Guide with T-Track

5 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Wonderful little gem!
I have started saving atleast 10 mins on every straight cut. Routing is made so easy with this wonderful little gem. Lay it over, clamp it and forget about it until the cut is complete. This is great for small projects, if you need to cut the 4x8 sheets, I would recommend the 50" clamp.

All in One Clamp C-50 50-Inch Single Grip Bench Clamp with T-track

4 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Excelent easy to use tool - Recommended.
I bought the T-50 50" Double Grip Bench Clamp with T-track for a large acrylic project. Cell cast acrylic sheets, 1/2 and 3/8" thickness, were cut with the T-50 as a guide for my circular saw. The T-50 is light for its size, is easy to allign and clamps well - lots of force and without losing my allignment. It held the acrylic well while the cuts were made - even 48" cuts while clamped on smooth ...

All in One Clamp A-50 50-Inch Grip Clamp Guide w/T-track

28 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Worth the money in the time it saves.
I purchased this a few weeks ago (from Amazon) with the wide jaws because of the recommendations here. I agree buy the jaw set, in fact I think they should just be sold as one unit. I am very pleased and did not have any problems using the tool. It sure beats using a board and clamps. The distance from the edge of my saw's baseplate to the blade is not a nice even number. I made a little ...

All in One Clamp SP 9-Inch X 12-Inch Saw Plate

4 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Cleaner Quicker more Accurate Cuts
I found this plate easy to mount as there is a built-in lip to clamp or hold your saw plate against during installation. My installation was fast and true (the squarer the installation the closer your cut width will be to the width of your blade). I went out and got an inexpensive but fairly strong (13 amp) circ saw and put a good blade on it so I could keep it permanently mounted thus ...

All in One Clamp U-54 54-Inch Ultra Wide Grip Clamp with Double T-Track

9 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Works great but is not idiot proof
If you expect to take this out of the box, throw it on top of a piece of plywood and have it automatically square and clamp itself you need to look elsewhere, maybe hire a cabinetmaker. If however you have a lot of experience in cutting panel materials with a portable circular saw you will find this a godsend. It is straight and clamps hard and that is all a craftsman expects. Expect that ...

All in One Clamp RP 8-Inchx 9-Inch Router Plate

6 reviews

E. Emerson Tool Co

E. Emerson Tool Co

A definate improvement over the clamp by itself
I used this with an all in one clamp I purchased at another store. I was cutting a 1/4 inch dado into 3/4 oak ply. I made test cuts with and without the plate using a 2 1/4 HP Bosch router. I found the cuts with the plate much easier. Installaton was a snap because there were predrilled holes for my router base. Simple product to use, and it make the job a lot easier. Please take into ...

All in One Clamp A-24 24-Inch Grip Clamp Guide w/T-track

7 reviews

E. Emerson Tool Co

E. Emerson Tool Co

I love these
I have four All in One clamps: 12", 24", 50", and 99", and I love them. The tape measures aren't accurate but I don't care because I only use these as straight edges that clamp onto the work piece, and they work great for that. I use them with both my router and my circular saw. Great phone support as well if you need to call them. Note that the part that slides requires you to push it up ...

All in One Clamp SB Stop Block w/ Micro Adjustment

E. Emerson Tool Co

E. Emerson Tool Co

The E. Emerson Tool Company SB All-in-One Stop Block features table extension capability for big jobs and micro-adjustment capability with a lock nut to handle tricky jobs. It's easy to set up the stop, and rugged ABS construction means you'll be using this tool for years to come.

All in One Clamp WJ Wide Jaws (2-Pack)

5 reviews

E. Emerson Tool Co

E. Emerson Tool Co

What the heck
I do not own this either, but thought I would balance the other reviews of guys who do not own this. I have the straight edge and it is nice. This is just the wide jaw clamps. I do not know how they could make it clearer.

All in One Clamp A-12 12-Inch Grip Clamp Guide with T-Track

1 review

E. Emerson Tool Co

E. Emerson Tool Co

Good clamp
Mine did not come with scales on the side as shown in the picture.

All in One Clamp I-50 50-Inch Scale (English)

2 reviews

E. Emerson Tool Co

E. Emerson Tool Co

No clue
I thought I was ordering the little knob in the picture not the scale. Oh well, for 99 cents and free shipping it may be useful someday.

All in One Clamp TJ Tall Jaws Set of 2

2 reviews

E. Emerson Tool Co

E. Emerson Tool Co

Holding Power for All in One Clamp
When using the All in One Bench Clamps these Tall Jaws give a good grip. I especially like them with the Double Grip Bench Clamps, I put them on the bottom and whatever I attach the clamp to it grips extra tight.All in One Clamp T-50 50-Inch Double Grip Bench Clamp with T-track